Plumbing Basics: A Must for Installing a Bathtub
Plumbing Basics: A Must for Installing a Bathtub
Blog Article
Are you on the lookout for answers on How to Install a Bathtub?
Mounting a bath tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is readily accessible, the job can move quickly; if you need to open a wall surface to remove the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will require a helper to leave the old tub and embeded in the new one. Make sure you have certified on your own for the job as well as fit attempting it. Rather than working with a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will help you mount a new bathtub in your washroom if you have currently bought a brand-new bathtub as well as don't require to change the plan of your previous water supply pipelines.
Your devices as well as product checklist must comprise the following:
Getting ready for the Setup
Firstly, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain any water staying in the system. The process of removing the existing taps can be quite problematic due to the restricted gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Utilizing both wood boards under its feet, place the bath tub in the called for setting. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as readjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest versatile faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water supply as well as examine all joints and also brand-new pipework for leaks and tighten them if needed. Fill the tub and additionally examine the overflow outlet and also the typical outlet for leakages.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the tub must wait till the bathtub has been utilized at the very least when as this will settle it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet as well as the sink. Secure the tap in position with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The former kind must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, resulting in problems with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can split rather very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads on How to Install a Bathtub Yourself, I was thinking sharing that excerpt was a great idea. Do you know somebody else who is intrigued by the niche? Feel free to promote it. Many thanks for your time. Don't forget to come by our website back soon.
Toilet overflow? Dial! Report this page